DIY Macrame Plant Hanger Using An Empty Tin Can
Hanging planters come in all shapes and sizes and they can be made from a diversity of different materials. They're fifty-fifty easy to arts and crafts at home and, in fact, this would be a lovely projection for the weekend. This step-by-footstep tutorial will explicate how you can make a cute macrame found hanger and a beautiful piddling planter to go with it.

Materials needed for the macrame establish hanger:
- tin
- bonding primer
- acrylic paint
- paintbrush
- silk ribbon
- macrame yarn
- hot mucilage gun
- scissors
- wood hoop

How to make a macrame establish hanger: stride-by-step tutorial
Pace 1: Apply a glaze of primer onto the tin
Get-go things first, make certain the tin is clean and dry. Launder information technology and remove any labels and mucilage before you start applying the primer. The surface should be smooth and have equally few imperfections as possible. So employ a coat of primer around the outside of the tin cans using the painbrush. Allow it to dry before you proceed to the next step.



Step ii: Pigment the tin
After the primer has dried start applying a glaze of acrylic pigment on superlative of it. Start from either the top or the bottom of the tin, slowly rotating it on your hand until y'all encompass the entire surface. Make certain you paint the bottom as well. Once the paint is dry, take a wait and decide if you want to apply a second glaze in order to cover upwardly whatever imperfections and to go a smoother and deeper color. Usually two coats are needed.






Step iii: Decorate the top and lesser with ribbon
After the second coat of paint has dried, apply a thin line of hot glue around the pinnacle of the can and then wrap a piece of ribbon around the edge, gently pressing it downward to go a smoothen surface. Cut off the excess ribbon and do the same thing for the bottom of the tin. The ribbon can be as thin or equally broad as you want it to be and in whatever colour you prefer. We chose a calorie-free blue nuance which matches the colour of the tin.










Step four: Cut four lengths of macrame yarn and line them upwardly
Next, measure and cut four long pieces of macrame yarn and fold each i in half so the ends line upward. Depending on how low you want your planter to hang yous can make these yarn pieces longer or shorter. Make sure they all accept the same dimensions. It's amend to make them alightly longer than necessary and to cut off the excess than to realize the hanger is also short in the stop.




Stride five: Loop the yarn through the wooden band
Have your four pieces of yarn and loop the folded ends through the wooden rings, then make a simple loop knot. This style it'southward sit squeamish and tight equally you continue to the next stride.




Step 6: Divide the yarn into four sections and tie a knot on each 1
Carve up the yarn into four equal sections, two strands each and spread them out on a flat surface, keeping the wooden ring at the center. A few inches downward from the ring, tie a knot on each section. Try to maintain the aforementioned length on each section.






Step 7: Tie together strands from adjacent sections
Now have ii strands of yarn from 2 adjacent sections and necktie them together in a knot a couple of inches below the initial ane. Do this for all four sections. They'll all exist linked together at this point.






Stride 8: Repeat the same process once again
Subsequently you've tied the adjacent strands together, repeat the same process once over again. This fourth dimension take 2 adjacent strands from the sections yous're previously tied together and tie another knot a couple of inches below the 1 to a higher place. Do this for all the yarn sections.




Pace nine: Place the tin inside the macrame hanger and tie the yarn into a knot at the bottom
Take the painted can and position it inside the macrame hanger you only made. Assemble all the yarn strands in a bunch at the bottom and decide how low you lot should tie the knot in order for your planter to sit down at the right height. Then necktie all the yarn strands into a big knot centered on the bottom of the can. Cutting the excess yarn so all the strands have the same length and form a tassel at the lesser of your hanging planter. That's it, you're done!







Source: https://www.homedit.com/macrame-plant-hanger/
0 Response to "DIY Macrame Plant Hanger Using An Empty Tin Can"
Post a Comment